Investigation of thermal residual stresses during laser ablation of tantalum carbide coated graphite substrates using micro-Raman spectroscopy and COMSOL multiphysics

Laser ablation of high-temperature ceramic coatings results in thermal residual stresses due to which the coatings fail by cracking and debonding. Hence, the measurement of such residual stresses during laser ablation process holds utmost importance from the view of performance of coatings in extreme conditions. The present research aims at investigating the effect of laser parameters such as laser pulse energy, scanning speed and line spacing on thermal residual stresses induced in tantalum carbide-coated graphite substrates. Residual stresses were measured using micro-Raman spectroscopy and correlated with Raman peak shifts. Transient thermal analysis was performed using COMSOL Multiphysics to model the single ablated track and residual stresses were reported at low, moderate and high pulse energy regimes. The results showed that the initial laser conditions caused higher tensile residual stresses. Moderate pulse energy regime comprised higher compressive residual stresses due to off centre overlapping of the laser pulses. Higher pulse energy (250 μJ), higher scanning speed (1000 mm/s) and moderate line spacing (20 μm) caused accumulation of tensile residual stresses during the final stage of laser ablation. The deviation of experimental residual stresses from COMSOL numerical model was attributed to unaccounted additional stresses induced during thermal spraying process and deformation potentials in the numerical model.     

Influence of Al3+ doping for V5+ on the structural,optical, thermal and electrical properties of V2-xAlxO5-δ (x=0–0.20) ceramics

This paper reports an investigation on the structure-properties correlation of trivalent metal oxide (Al₂O₃)-doped V₂O₅ ceramics synthesized by the melt-quench technique. XRD patterns confirmed a single orthorhombic V₂O₅ phase formation with increasing strain on the doping of Al₂O₃ in place of V₂O₅ in the samples estimated by Williamson-Hall analysis. FTIR and Raman investigations revealed a structural change as [VO₅] polyhedra converts into [VO₄] polyhedra on the doping of Al₂O₃ into V₂O₅. The optical band gap was found in a wide semiconductor range as confirmed by UV–visible spectroscopy analysis. The thermal and conductivity behavior of the prepared samples were studied using thermal gravimetric analysis (TGA) and impedance analyzer, respectively. All the prepared ceramics exhibit good DC conductivity (0.22–0.36 Sm^-1) at 400 ?C. These materials can be considered for intermediate temperature solid oxide fuel cell (IT-SOFC)/battery applications due to their good conductivity and good thermal stability.     

La2O3对SiO2-CaO-Al2O3-MgO熔体黏度和结构的影响

使用分析纯物质模拟微晶玻璃熔体，分别采用柱体旋转法和拉曼光谱技术研究了La2O3含量对SiO2-CaO-Al2O3-MgO熔体黏度和结构的影响规律。结果表明：熔体黏度和黏流活化能随着La2O3含量的增加而降低；拉曼光谱表明La2O3能破坏硅酸盐结构（Qn），随着La2O3含量的增加，Q1、Q2的百分含量增加，Q3的百分含量减小，Q0的百分含量基本不变，表明熔体中非桥氧数量增加，熔体聚合度降低。La2O3在熔体中起网络修饰体的作用。     

Micro-structural study of Yaozhou celadons (Tang to Yuan Dynasty): probing crystalline and glassy phases

The Yaozhou kiln complex is a representative production center of ancient northern China, famous for the celadon production. In this work, bubbles, glassy matrix and residual crystals of celadon glazes produced from the Tang to Yuan Dynasty were analyzed by using optical microscopy, Raman spectroscopy and scanning electron microscopy-energy dispersive X-ray spectroscopy (SEM-EDS). The results revealed that the Song, Jin and Yuan productions present bigger bubble and higher area ratios of the Si-O bending over stretching modes than the Tang and Wudai productions. This is consistent with firings at higher temperatures during Song, Jin and Yuan Dynasties. It is also in agreement with the historical studies, which revealed the change from wood-firing to coal-firing during Song Dynasty. The observation of calcium phosphate in Yaozhou productions indicated that the glaze ash had been used. No iron-based particle was identified by Raman spectroscopy in the glazes of all periods. The green color is certainly due to iron ion dispersed in the glassy matrix. Our study also confirmed no significant change in glaze raw materials used for Yaozhou productions from Tang to Yuan Dynasty.     

Enhanced properties for visible-light-driven photocatalysis of Ag nanoparticle modified Bi2MoO6 nanoplates

The visible light driven Bi₂MoO₆ photocatalyst doped with different contents of Ag nanoparticles was successfully synthesized by a combination of hydrothermal and sonochemical methods. The as-synthesized samples were characterized by X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), scanning and transmission electron microscopy (SEM and TEM) and UV–visible spectroscopy to investigate crystalline structure, morphology, composition and photocatalytic properties. XRD patterns and TEM images of the samples revealed pure phase orthorhombic Bi₂MoO₆ nanoplates without any detection of Ag dopant due to its low concentration and very tiny particle size. TEM images showed that Ag nanoparticles with the size of 10–15 nm were dispersed randomly on the surface of Bi₂MoO₆. The XPS analysis of Ag/Bi₂MoO₆ nanocomposites revealed the presence of additional metallic Ag. Photocatalytic activities of the Ag/Bi₂MoO₆ nanocomposites were evaluated by determining the degradation of rhodamine B (RhB) under visible light radiation. In this research, the 10 wt% Ag/Bi₂MoO₆ nanocomposites showed the best photocatalytic activity. The results suggest that the dispersion of Ag nanoparticles on the surface of Bi₂MoO₆ significantly enhances its photocatalytic activity.     

Raman and X-ray photoelectron spectroscopy study on the influence of La2O3 on the melt structure of SiO2–CaO–Al2O3–MgO

In order to gain more insights into the influence of rare earth elements on the melt structure of SiO₂–CaO–Al₂O₃–MgO glass ceramics, Raman and X-ray photoelectron spectroscopy techniques were used to study the influence of La₂O₃ on the Si–O/Al–O tetrahedron structure within SiO₂–CaO–Al₂O₃–MgO–quenched glass samples in this study. Results showed that some Raman peak shapes at low frequencies (200–840 cm^?1) changed significantly after the addition of La₂O₃, compared to the high frequency (840–1200 cm^?1) region that corresponds to the [SiO₄] structure, suggesting that the depolymerization of the low-frequency T–O–T (T=Si or Al) structure was more prevalent with La³⁺ addition. Besides, the depolymerization extent of the Si–O/Al–O tetrahedral network varied when the melt composition altered. Most notably, depolymerization is the most significant at a low CaO/SiO₂ ratio (0.25) and a high Al₂O₃ content (8%). Meanwhile, La³⁺ can promote the transformation of Si–O–Si and Al–O–Al bonds to the Si–O–Al ones, thereby forming a complex ionic cluster network interwoven with Si–O and Al–O tetrahedrons.     

Experimental investigation of Co and Fe-Doped CuO nanostructured electrode material for remarkable electrochemical performance

The current research work presents a facile and cost–effective co-precipitation method to prepare doped (Co & Fe) CuO and undoped CuO nanostructures without usage of any type of surfactant or capping agents. The structural analysis reveals monoclinic crystal structure of synthesized pure CuO and doped-CuO nanostructures. The effect of different morphologies on the performance of supercapacitors has been found in CV (cyclic voltammetry) and GCD (galvanic charge discharge) investigations. The specific capacitances have been obtained 156 (±5) Fg^?1, 168(±5) Fg^?1 and 186 (±5) Fg^?1 for CuO, Co-doped CuO and Fe-doped CuO electrodes, respectively at scan rate of 5 mVs^?1, while it is found to be 114 (±5) Fg^?1, 136 (±5) Fg^?1 and 170 (±5) Fg^?1 for CuO, Co–CuO and Fe–CuO, respectively at 0.5 Ag^-1 as calculated from the GCD. The super capacitive performance of the Fe–CuO nanorods is mainly attributed to the synergism that evolves between CuO and Fe metal ion. The Fe-doped CuO with its nanorods like morphology provides superior specific capacitance value and excellent cyclic stability among all studied nanostructured electrodes. Consequently, it motivates to the use of Fe-doped CuO nanostructures as electrode material in the next generation energy storage devices.     

Synthesis of Diamond@SiO2@Ag composite materials for high SERS effect

Among various carbon materials, diamond stands out due to excellent physical and chemical properties. In this work, we designed Dia@SiO₂@Ag composites combining diamond micropowder and Ag nanoparticles by a simple chemical method and obtained stable substrate for surface enhanced Raman scattering (SERS) owing to its high surface-to-volume ratio, low density, as well as close bond between diamond and Ag. As-prepared Dia@SiO₂@Ag presented high activity to detect crystal violet and rhodamine 6G molecules, which was demonstrated by significantly enhanced SERS spectra and high enhancement factor values (10⁸-10⁹). Moreover, Dia@SiO₂@Ag also showed desired sensitivity, which was investigated by detection limit. Therefore, our study provided more theoretical support and broadened the functional applications of diamond, particularly in Raman detection.     

Formation of ST12 phase Ge nanoparticles in ZnO thin films

In this work, we focus on the Ge nanoparticles (Ge-np) embedded ZnO multilayered thin films. Effects of reactive and nonreactive growth of ZnO layers on the rapid thermal annealing (RTA) induced formation of Ge-np have been specifically investigated. The samples were deposited by sequential r.f. and d.c. sputtering of ZnO and Ge thin film layers, respectively on Si substrates. As-prepared thin film samples have been exposed to an ex-situ RTA at 600 °C for 60 s under forming gas atmosphere. Structural characterizations have been performed by X-ray Diffraction (XRD), Raman scattering, Secondary Ion Mass Spectroscopy (SIMS), and Scanning Electron Microscopy (SEM) techniques. It has been realized that reactive or nonreactive growth of ZnO layers significantly influences the morphology of the ZnO: Ge samples, most prominently the crystal structure of Ge-np. XRD and Raman analysis have revealed that while reactive growth results in a mixture of diamond cubic (DC) and simple tetragonal (ST12) Ge-np, nonreactive growth leads to the formation of only DC Ge-np upon RTA process. Formation of ST12 Ge-np has been discussed based on structural differences due to reactive and nonreactive growth of ZnO embedding layer.     

Improved optical and structural properties of cadmium sulfide nanostructures for optoelectronic applications

In this study, the effect of ZnO seed layer on the growth of uniform CdS nanostructures was investigated using chemical bath deposition technique. Besides, the influence of molar concentration of reagents on the surface morphology, structural and optoelectrical properties of the deposited CdS thin films were examined. The CdS nanostructures were grown on bare glass and ZnO/glass substrates with different reagent molar concentrations. The results indicated an improvement in the homogeneity and uniformity of the grown CdS nanostructures on ZnO seed layer which can be due to the low lattice mismatch between ZnO and CdS structures. The CdS/ZnO samples were optimized by changing the molar concentration of reagents. A three–dimensional intersecting vertical nanosheet morphology with hexagonal structure was obtained when modified chemical concentration of 0.5 M was applied. The XRD pattern of CdS nanosheets indicated the hexagonal phase of CdS which were strongly orientated along (002) plane. The elevated intensity of dominant peak related to this sample confirmed the improved crystal quality of this CdS nanostructure comparing to the other samples. The UV–Vis spectrum demonstrated a high absorption coefficient for CdS intersecting nanosheets which might be due to the high specific surface area and light trapping behavior of this sample. The photoluminescence study also showed an improvement in optical properties of optimized CdS nanostructures. In order to study the optoelectrical properties of CdS nanostructures, metal–semiconductor–metal photodetectors were fabricated with different CdS samples and their current–voltage characteristics were analyzed. The results indicated an enhancement in photosensitivity, responsivity, and speed of photodetectors based on optimized CdS nanostructures.